AIRTRONICS MT-4s Betriebsanweisung PDF herunterladen (Seite 35)

T R



The Point Auxiliary function allows you to program the Auxiliary 2 servo to move up to 6 different Points along its travel, then

cycle through those Points using one of the Trim Switches or the Rotary Dial. For example, if your model requires a separate

3-position or more switch to operate a feature, the Point Auxiliary function can be customized to control this.

Use one of the four Trim Switches or the Rotary Dial to cycle through the Point positions while you're driving. The Point

Auxiliary function can be toggled OFF and ON while you're driving by assigning Auxiliary 2 to one of the two Push-Button

Switches. To ensure correct operation, make sure to refer the Important notice in the Controlling the Point Auxiliary Function below.



















Choosing the Point Auxiliary Function and the Number of Points:

1) From the Top Screen, press the ENTER key to open the Programming Menu list.

2) Scroll UP or DOWN to highlight the SYSTEM menu, then press the ENTER key. Scroll

DOWN to highlight the AUX TYPE menu, then press the ENTER key.

3) Press the ENTER key, then scroll UP or DOWN to choose the AUX2: POINT AUX function.

4) From within the AUX TYPE menu, scroll DOWN to highlight [MODE] 6 POINT. Press the

ENTER key, then scroll UP or DOWN to choose the desired number of Points you would

like to program.

AUX TYPE POINT setting range is 2point to 6point. The default setting is 6point.

Adjusting the Point Auxiliary Values:

1) From the Top Screen, press the ENTER key to open the Programming Menu list.

2) Scroll UP or DOWN to highlight the AUX2 menu, then press the ENTER key. The AUX2

POINT menu will be displayed and the last Point selected will be highlighted.

3) Scroll UP or DOWN to move the brackets to the Point you would like to change, then

press the ENTER key to highlight that Point.

4) Press the ENTER key, then scroll UP or DOWN to change the Point value. Increasing the

Point value toward the High side (H) or Low side (L) will cause the Auxiliary 2 servo to

travel to that specific position when you cycle through the various Points.

5) Repeat steps 3 and 4 to change the desired remaining Point values.

AUX2 POINT setting range is H100 to L100. The default setting for Point 1 is L100, for Point 2 is L60, for Point 3 is L20, for Point 4

is H20, for Point 5 is H60, and for Point 6 is H100. These values are a percentage of Auxiliary 2 servo travel.

Controlling the Point Auxiliary Function:

1) In the default configuration, Auxiliary 2 is controlled by the Auxiliary Lever, however, we suggest re-assigning this function

to the Rotary Dial or one of the Trim Switches to make it easier to adjust while driving. Turn the Rotary Dial clockwise to cycle

Forward through the programmed Point Auxiliary positions and turn the Rotary Dial counter-clockwise to cycle Backward

through the programmed Point Auxiliary positions. The Auxiliary 2 servo will move to the specified Point positions as

you cycle through the different Points.

In addition, the Point Auxiliary function can be toggled OFF and ON by assigning Auxiliary 2 to one of the two Push-Button

Switches. For more information, see the Key Assignments section on pages 53 through 58.

IMPORTANT: To operate correctly, the TRIM or DIAL Step value must be set to 1. If set to a value other than 1, Point positions

will be skipped as you cycle through them. For more information, see the Key Assignments section on pages 53 through 58.

PROGRAM

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 87 88

Kommentare zu diesen Handbüchern

Keine Kommentare

AIRTRONICS MT-4s Betriebsanweisung Seite 35

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fernbedienungen AIRTRONICS MT-4s