18
6) After changing the desired Programming Value, press the ENTER key or the BACK/CANCEL key and the highlighted option
will stop flashing, indicating you can scroll UP or DOWN to highlight another programming option.
7) To change to another channel, press the BACK/CANCEL key, then scroll UP or DOWN to select the desired channel. Repeat
steps 4 and 5 above to change the desired Programming Values for that channel.
8) When complete, press and HOLD the BACK/CANCEL key to return to the Top Screen.
01.D/R - RATE
02.EPA - L/R
03.EPA - LEFT
04.EPA - RIGHT
05.CURVE - RATE
06.CURVE - POINT
07.SPEED - FORWARD
08.SPEED - RETURN
09.TRIM
10.SUB-T
11.REV - NOR/REV
12.F/S
01.D/R - TH
02.D/R - BR
03.EPA - HIGH
04.EPA - LOW
05.CURVE - RATE-H
06.CURVE - POINT-H
07.CURVE - RATE-B
08.CURVE - RATE-H
09.SPEED - FORWARD
10.SPEED - RETURN
11.ALB - POINT
12.ALB - STROKE
13.ALB - LAG
14.ALB - RELEASE
15.ALB - HOLD
16.TRIM
17.SUB-T
18.REV - NOR/REV
19.F/S
01.EPA - HIGH
02.EPA - LOW
03.CURVE - RATE
04.CURVE - POINT
05.CURVE
06.CURVE
07.SPEED - FORWARD
08.SPEED - RETURN
09.TRIM
10.SUB-T
11.REV - NOR/REV
12.F/S
01.EPA - HIGH
02.EPA - LOW
03.CURVE - RATE
04.CURVE - POINT
05.CURVE
06.CURVE
07.SPEED - FORWARD
08.SPEED - RETURN
09.TRIM
10.SUB-T
11.REV - NOR/REV
12.F/S
[
ST
]
STEERING
[
TH
]
THROTTLE
[
A1
]
AUXILIARY 1
[
A1
]
AUXILIARY 2
The Dual Rate function allows you to change the control authority of the Steering, Throttle High Side and Throttle Brake Side by
changing the amount of servo travel relative to control input. For example, by increasing the Steering Dual Rate, you can make
the steering servo travel more, which might prevent your model from pushing during turns. If your model oversteers during
turns, you can reduce the amount of Steering Dual Rate. Adjusting Steering Dual Rate affects both Right-hand and Left-hand
steering equally, however, you are able to adjust Throttle Dual Rate on the Throttle High Side and Throttle Brake Side independently.
IMPORTANT: Prior to programming the Dual Rate function, you should adjust the maximum Left and Right (or High and Low)
End Points, using the End Point Adjustment function. For more information, see the End Point Adjustment section on pages
19 through 21.
4) Press the ENTER key to highlight the Programming Value in the upper right corner.
5) Scroll UP or DOWN to highlight the Programming Value you would like to change, then
press the ENTER key to select it. The highlighted Programming Value will flash
indicating you can change the Programming Value. Scroll UP or DOWN to change the
Programming Value
The following functions can be programmed from within the Channel Set menu:
Dual Rate is a percentage of End Point Adjustment. For example, if you set the Steering Dual Rate percentage value to
100%, the Steering will travel the same amount defined by your End Point Adjustment programming. Alternately, if you set
the Steering Dual Rate percentage value to 50%, the Steering will travel half the amount defined by your End Point Adjustment
programming.
(24 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern