AIRTRONICS MX-V Betriebsanweisung PDF herunterladen (Seite 4)

V 3

CHANNEL 2.4GHZ RADIO SYSTEM USER'S GUIDE

2.4GHZ fREqUENCY bAND PRECAUTIONS

• The 2.4GHz frequency band may be used by other devices, or other devices in the immediate area may cause interference on

the same frequency band. Always before use, conduct a bench test to ensure that the servos operate properly. Also, conduct

checks with the transmitter as distant as possible from your model.

• The response speed of the receiver can be affected if used where multiple 2.4GHz radio controllers are being used, therefore,

carefully check the area before use. If response seems slow during use, stop your model immediately and discontinue use.

• If the 2.4GHz frequency band is saturated (too many radio controllers on at once), as a safety precaution, the radio control

system may not bind. This ensures that your radio control system does not get hit by interference. Once the frequencies have

been cleared, or the saturation level has dropped, your radio control system should be able to bind without any problems.

TRANSMITTER PRECAUTIONS

• To prevent possible damage to your servos or a runaway model, turn the transmitter ON first, then turn

the receiver ON. After running your model, turn the receiver OFF first, then turn the transmitter OFF.

• Before use, double-check that the transmitter and receiver batteries have sufficient power.

• The transmitter features an internal antenna installed inside the front portion of the transmitter.

Do NOT cover the front of the transmitter in any way during use! Doing so can block the RF signal, resulting in loss

of control of your model.

• During use, hold the transmitter so that its orientated as close to vertical as possible at all times. This provides the best RF

signal between the transmitter and the receiver. Try not to ever 'follow' your model with the transmitter, as this can result in a

weakened RF signal.

• Do not expose the transmitter or any other components to excessive heat, moisture, fuel, exhaust residue, etc.

• Do not press the Bind Button during use. The signal is interrupted while the Bind

Button is pressed. It may also require a short time to restore the signal after

releasing the Bind Button, which can be dangerous.

• If the outer case becomes dirty, it can be cleaned with a soft dry cloth. If the outer case becomes

soiled, it can be cleaned with a damp cloth and liquid detergent.

• Do not use any solvents to clean the outer case. Solvents will damage the finish.

• The antenna wire is delicate, therefore, handle with care. Do not pull on the antenna wire with force.

• Do not cut the antenna wire shorter or extend the antenna wire.

• The antenna wire can be bent into gentle curves, however, do not bend it acutely, or repeatedly bend it, or the antenna wire

can be damaged.

• The antenna wire should be installed into a vertical plastic tube per your particular model's assembly

instructions. Keep the receiver antenna as far away from the motor, battery and ESC as possible.

• There is a danger of runaway operation if connectors shake loose during use. Make sure that the receiver,

servo(s) and switch connectors are securely fitted.

• The receiver is susceptible to vibration, shock and moisture. Take appropriate measures to protect against vibration and

moisture. Failure to take appropriate measures could result in runaway operation or damage to the receiver. We suggest

wrapping the receiver in shock-absorbing foam or securing it with double-sided foam tape when installing it into your model.

• When installing the receiver and routing the receiver antenna, avoid contact with any carbon or metal chassis components.

Contact between metal parts mounted on a model can result in electrical noise, which can adversely effect receiver

performance and possibly result in runaway operation or damage to your model.

• With electric-powered models, be sure to fit any brushed motors with a noise suppression capacitor. Without a noise suppression

capacitor, excessive electrical noise generation can cause runaway operation and/or result in damage to your model.

• The receiver does not feature BEC circuitry. If using an electronic speed control, verify that it features BEC circuitry to drop

the receiver voltage between 4.8v to 7.4v.

RECEIVER PRECAUTIONS

The receiver included with your radio control system uses Airtronics 'Z' connectors, which are electronically compatible with the

servos of other radio control system manufacturers. The connectors are rugged, but should be handled with care.

When unplugging the servo connector, don't pull on the servo wire itself. This could result in damage to the servo wire pins

in the plastic plug. Always grasp the plastic connector itself.

SERVO CONNECTORS

- = Negative (Black)

+ = Positive (Red)

S = Signal (Blue)

If using another brand of servo, double-check the polarity

of the servo connector prior to plugging it into the receiver.

1 2 3 4 5 6 7 8 9 ... 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

AIRTRONICS MX-V Betriebsanweisung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fernbedienungen AIRTRONICS MX-V