AIRTRONICS MX-V Betriebsanweisung PDF herunterladen (Seite 20)

V 3

CHANNEL 2.4GHZ RADIO SYSTEM USER'S GUIDE

Binding: The act of pairing the transmitter and receiver to prevent interference from transmitters operated by other users. The

transmitter and receiver must be paired so that the two can 'talk' to each other. Once the binding procedure is complete, the

setting is remembered even when the transmitter and receiver are turned OFF.

Bind Button: Used in the process of binding the transmitter and receiver.

Bind LED: Displays the current status of the receiver.

Brake Side: Refers to the throttle trigger stroke that engages the brakes on your model (pushing the throttle trigger).

Decrease Key: Decreases Programming Values and used to select models. Press the INCREASE and DECREASE keys at the

same time to reset Programming Values to default.

Digital Trim Memory: Allows the transmitter to store Trim values in its memory. Any amount of Trim that you set during use using

the Trim Switches is automatically stored in memory for that specific channel and for that specific model. The Trim values for

each model will automatically be loaded when the transmitter is turned ON.

Dual Rate: Used to change the control authority of your model's steering by changing the amount of servo travel relative to

control input.

DS2 Modulation: A Modulation Type typically used in Japan. This Modulation Type is not used in North America.

End Point Adjustment: Used to adjust the desired amount of servo travel in both directions independently. This makes it possible

to balance servo travel in both directions.

Exponential: Allows you to vary the amount of servo travel in relation to the movement of the steering wheel and throttle trigger

near the Neutral positions to change the way those functions react to control movement.

Fail Safe: Automatically moves the throttle servo to a predetermined position in the event that the signal between the transmitter

and the receiver is interrupted, whether due to signal degradation or low transmitter battery. This helps prevent the chance of a

runaway model, should the transmitter lose power or the signal between the transmitter and receiver be lost.

FH2 Modulation: Frequency Hopping 2nd generation FHSS technology. FH2 modulation is safe, fast and reliable.

FH2F Modulation: A Modulation Type typically used in France. This Modulation Type is not used in North America.

FHSS: Frequency Hopping Spread Spectrum. FHSS is a Modulation Type which transmits data across the entire frequency

spectrum by transmitting data on different channels at an extremely fast interval.

Forward Side: Refers to the throttle trigger stroke that opens the throttle and powers your model (pulling the throttle trigger).

Grip: The grip is molded in an ergonomic shape for increased comfort, control and feel. It's moulded with a textured surface to

help prevent slipping.

High Side: Refers to the position of Auxiliary channel 3 servo movement (pushing the Auxiliary Lever up).

Increase Key: Increases Programming Values and used to select models. Press the INCREASE and DECREASE keys at the same

time to reset Programming Values to default.

Low Side: Refers to the position of Auxiliary channel 3 servo movement (pushing the Auxiliary Lever down).

Low Voltage Alarm: Warns you when the transmitter batteries need to be replaced or recharged (if using rechargeable batteries).

The Low Voltage Alarm will sound when the transmitter batteries reach 4.6 volts. If the Low Voltage Alarm sounds while you are

driving, you should stop as soon as it's safe, then replace or recharge the transmitter batteries.

LCD Screen: The heart of the programming and display features of the transmitter. All programming and transmitter display

functions are shown on the LCD screen.

Menu Selections: Displays the available Programming Menus. The currently Active menu will flash. The information displayed in

the Programming Window will vary based on the menu selected.

Menu Down Key: Cycles down through the list of menus and sub-menu functions you would like to make programming changes

to. Press the MENU UP and MENU DOWN keys at the same time to display the Voltage Monitor.

Menu Up Key: Cycles up through the list of menus and sub-menu functions you would like to make programming changes to.

Press the MENU UP and MENU DOWN keys at the same time to display the Voltage Monitor.

Model Naming: Used to name the different models you have saved in the transmitter. This makes it easy to keep track of multiple

models. The Model Name can consist of up to 3 letters, numbers or symbols.

Model Number: Displays the model that is currently loaded into memory. Up to 10 different models can be stored.

Model Select: Used to store and retrieve Programming Data for any model 1 through 10. If you have Programming Data stored

for more than one model, use the Model Select function to load the Programming Data for the particular model that you wish to

drive. The currently selected Model Number is displayed next to the Voltage Monitor.

Operating Voltage: The safe voltage that the transmitter can operate within. Exceeding the minimum operating voltage can

result in loss of power to the device. Exceeding the maximum operating voltage can result in damage to the device.

Output Power: The power (in Milliwatts) that your transmitter transmits a signal. Output power is defined by government

guidelines and differs by region.

Power Indicator: Illuminates red, indicating the transmitter is turned ON.

GLOSSARY Of TERMS

1 2 ... 15 16 17 18 19 20 21 22 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

AIRTRONICS MX-V Betriebsanweisung Seite 20

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fernbedienungen AIRTRONICS MX-V