AIRTRONICS MX-V Spezifikationen PDF herunterladen (Seite 9)

Page 9





Instead of using Alkaline batteries to power the transmitter and receiver, you can use rechargeable Ni-Cd or Ni-MH

batteries. This will provide longer usage time and reduced cost in the long run, since you won't need to continuously

purchase new Alkaline batteries. The transmitter features a Charging Jack, which can be used with the optional

Airtronics 95033Z 110v AC Transmitter and Receiver dual charger to recharge the batteries without removing them

from the transmitter. In addition, this charger can also be used to recharge a 4.8v (4 cell) or 6.0v (5 cell) rechargeable

Ni-Cd or Ni-MH receiver battery pack at the same time. We recommend the following:

Hi-Energy 1200mAh Ni-MH 'AA' Rechargeable Batteries (4-Pack) for Transmitter (2 PCS.)

Hi-Energy 6.0v 1600mAh Ni-MH Rechargeable Hump Battery Pack for Receiver (1 PC.)

Airtronics 95033Z 110v AC Transmitter and Receiver Dual Charger (1 PC.)

1) Install the optional 1200mAh Ni-MH rechargeable batteries into the transmitter, following the steps in the Transmitter

Battery Installation section on the previous page, then connect your receiver battery using the diagram on the

previous page. If you're using an electronic speed control, you generally won't be using a separate receiver battery.



Torque: 80oz/in (5.8kg/cm @ 4.8v)

89oz/in (6.4kg/cm @ 6.0v)

Speed: 0.10 sec/60º @ 4.8v

0.08 sec/60º @ 6.0v

Dimensions: 1.59 x 0.83 x 1.04in

(40.4 x 21.1 x 26.4mm)

Weight: 1.77oz (50gr)

Torque: 42oz/in (3.0kg/cm @ 4.8v)

53oz/in (3.8kg/cm @ 6.0v)

Speed: 0.20 sec/60º @ 4.8v

0.16 sec/60º @ 6.0v

Dimensions: 1.54 x 0.79 x 1.42in

(39.1 x 20.0 x 36.0mm)

Weight: 1.59oz (45gr)

94780M Digital High-Power Metal Gear Dual Ball Bearing Servo

Torque: 361oz/in (26.0kg/cm @ 4.8v)

423oz/in (30.5kg/cm @ 6.0v)

Speed: 0.19 sec/60º @ 4.8v

0.15 sec/60º @ 6.0v

Dimensions: 1.60 x 0.83 x 1.50in

(40.6 x 21.1 x 38.1mm)

Weight: 2.33oz (66gr)

94102Z Standard Bushing Servo

Both analog and digital servos will work with your MX-Sport 2.4GHz FHSS-2 radio control system. To get the

most out of your experience, we recommend the use of digital servos.

94746M Digital Metal Gear Low-Prole Dual Ball Bearing Servo

Torque: 124oz/in (8.9kg/cm @ 4.8v)

151oz/in (10.9kg/cm @ 6.0v)

Speed: 0.17 sec/60º @ 4.8v

0.13 sec/60º @ 6.0v

Dimensions: 1.54 x 0.78 x 1.50in

(39.0 x 20.0 x 37.4mm)

Weight: 1.93oz (56gr)

94775M Digital High-Power Metal Gear Dual Ball Bearing Servo

Although most current brand servos will work with your MX-Sport 2.4GHz FHSS-2 radio control system, we

recommend using Airtronics brand servos. For pricing, availability, and more selection, please visit your local

Airtronics dealer or our website at http://www.airtronics.net.

Charging the Optional Ni-MH Transmitter and Receiver Batteries

The MX-Sport transmitter features a Charging Jack located on the left side of the transmitter, allowing you to

recharge the optional rechargeable batteries without removing them from the transmitter. Use ONLY the recommended

optional Airtronics 95033Z 110v AC Transmitter and Receiver dual charger or damage to the transmitter and/or

batteries could result.

1) Plug the Airtronics 95033Z 110V AC Transmitter and Receiver dual charger into a 110v AC wall socket.

2) Plug the round connector from the charger into the Charging Jack in the transmitter and plug the female

connector from the charger into the receiver battery. The charger LEDs will illuminate red, indicating that the

charger is charging.

3) Both transmitter and receiver charger outputs are 75mAh, therefore, it will take approximately 16 hours to recharge

fully-discharged 1200mAh batteries (1200/75=16). Charge time will vary depending on the mAh capacity of the

batteries you're charging. For example, 1600mAh batteries would require a 21 hour charge (1600/75=21).

WARNING Do NOT attempt to recharge Alkaline batteries. Do NOT attempt to charge any type of batteries

other than those recommended and use ONLY the recommended charger. Do not use the Charging Jack with

any after-market fast charger or Peak-Detection charger or the transmitter could be damaged.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

AIRTRONICS MX-V Spezifikationen Seite 9

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fernbedienungen AIRTRONICS MX-V